Poêle au gaz propane liquide en fonte sans évent de 1 500 pieds carrés - noir

Poêle au gaz propane liquide en fonte sans évent de 1 500 pieds carrés - noir

Le style classique en fonte avec une finition peinte en noir fait de ce magnifique poêle à gaz l'appareil de chauffage parfait pour tout espace de vie. La cuisinière à gaz Ashley Hearth AGC500VFLP fournit 32 000 BTU de chaleur de manière sûre et efficace. Parce qu'il ne nécessite pas d'évent, il est efficace 99%, ce qui vous assure d'en avoir pour votre argent à chaque fois que vous utilisez ce poêle. Un ensemble de bûches est inclus avec ce poêle pour vous donner un look de feu réaliste. De plus, ce poêle n'a pas besoin d'électricité pour fonctionner, ce qui signifie que c'est le poêle parfait à posséder en cas de panne de courant. Le fonctionnement standard est simple, il suffit d'allumer l'interrupteur, de sélectionner votre puissance calorifique et de profiter de la chaleur. Ce poêle est simple à utiliser et peut être connecté à n'importe quel thermostat millivolt standard lui permettant de s'allumer et de s'éteindre selon les besoins. Les poêles AGC500VF peuvent chauffer jusqu'à 1 500 m². Ft. et est disponible en modèles au gaz naturel ou au propane liquide (LP).

  • Modèle # : AGC500VFLP

  • Caractéristiques
    • Chauffe jusqu'à 1 500 pieds carrés avec 32 000 BTU
    • Type de combustible pour cuisinière à gaz : propane liquide (LP)
    • Comprend un écran de sécurité pour éviter les brûlures et un ensemble de bûches pour une flamme réaliste
    • Branchement du thermostat millivolt prêt avec un fonctionnement marche/arrêt facile
    • Finition noire peinte
    • Approuvé pour l'installation dans les maisons mobiles (États-Unis uniquement)
  • Caractéristiques
    Type de poêle Sur pied
    Produit Superficie de chauffage (pi²) 1500
    Longueur du produit (po) 29
    Produit ventilé ou sans ventilation Sans ventilation
    Souffleur de produits Non
    Garantie du fabricant du produit Chambre de combustion et vanne 3 ans. 1 an Cabinet et autres pièces.
    Système d'appauvrissement en oxygène du produit Oui
    Efficacité du produit 99
    Système d'allumage de produit Bouton Poussoir Piezo
    Télécommande de produit Non
    Hauteur du produit (po) 16
    Type de combustible pour cuisinière à gaz Propane
    Produit homologué UL Non
    Produit listé ETL Oui
    Largeur du produit (po) 26.0
    Produit Maximum BTU 32000
    Produit certifié CSA Non
    Couleur / Finition du produit Peinture noire
  • Dimensions
    Largeur assemblée (po) 26
    Poids du paquet 245
    Largeur du paquet 24
    Hauteur du colis 35
    Profondeur assemblée (in) 29
    Profondeur de l'emballage 31
    Hauteur assemblée (po) 16
  • Autre
    Nom de la marque MFG Produits de foyer Ashley
    Ce produit a-t-il une garantie ? Oui
    Modèle MFG # (Série) AGC500VFLP
    Garantie du fabricant Chambre de combustion et vanne 3 ans, armoire 1 an et autres pièces
    Type de garantie Limité - Pièces
    Type/Catégorie de produit du fournisseur Accueil - Chauffage, climatisation et qualité de l'air
    Rechercher des mots-clés Gaz, Propane, poêle, foyer, chauffage, Autonome, économique
    Type de garantie de date d'entrée en vigueur date d'achat
    CUP 012685704890
  • Réglementaire
    Avertissement de la Proposition 65 de la Californie requis Oui
    Contient des produits chimiques qui causent le cancer (Calif Prop65) Oui
    L'article a des restrictions ? Oui
    Énumérez les produits chimiques contenus qui causent le cancer selon la proposition 65 de la Californie Monoxyde de carbone
  • FAQ
    • I smell a gas odor when the control knob is in the off position. What do I do?
      • Gas leak:
        1. Do not try to light the appliance.
        2. Do not touch any electrical switch.
        3. Do not use any phone in the building.
        4. Have gas company come and locate the leak.
        5. If the gas company is unavailable have the fire department come and locate the leak.
      • Defective control valve – try to push down or turn the control knob. If it will not push down or turn, the control valve may be defective. **It may still be defective even if the control knob will move.
    • Why will my burner not light?
      • Burner orifice is clogged – clean the same way you would the pilot orifice.
      • Burner orifice diameter is too small – have a gas technician replace the orifice with the correct size.
      • Incorrect gas pressure – see below:
        1. Check that the manual shutoff valve is in the open position.
        2. Have the gas company check that the incoming gas line is pressurized correctly and is not leaking.
        3. If using propane-check that a large enough tank is being used (at least 100 gallon). If the tank has recently been refilled be sure that all the air has been flooded from the gas line.
        4. Have a gas technician check to see if the right size piping was used and if the gas regulator is set correctly.
    • What will cause my pilot to light, but go out when the control knob is released?
      • Control knob is not pressed in all the way – pressing the control knob down allows a flow of gas to the pilot assembly. If not pressed all the way down the pilot will not be self-sustaining.
      • Thermocouple – when the control knob is held down during ignition you are manually opening the gas valve to allow gas flow through the pilot assembly. During normal operation the thermocouple generates a small voltage that holds the gas valve open to allow gas flow. If the thermocouple is bad there will be no gas flow to the pilot assembly once the control knob is released.
        • The thermocouple connection may just be loose.
        • The pilot hood that directs the pilot flame towards the thermocouple may be bent and not allowing contact between the flame and thermocouple.
      • The pilot is clogged – over time a residue will buildup on the orifice and pilot components which will affect the flow of gas. Use a heavy duty pipe cleaner to clear the orifice opening (be sure not to enlarge the opening). Use a non-abrasive scouring pad to clean the thermocouple and other metal components. Use a mild soap and water solution…never anything flammable.
      • Control valve – it is possible that the control valve is damaged or faulty. The only option here is to replace it. This must be done by a licensed gas technician.
      • Orifice isn’t the right size – higher altitudes will affect the operation of a gas heater. Especially when using NG because it is lighter than air. A smaller orifice can be used to obtain the needed pressure at higher altitudes. These are not available through USSC.
    • Why will my pilot not light?
      • Loose ignitor wire – Remove the front cover and check to see if the ignitor wire has come lose. This can happen during shipping.
      • Bad piezo ignitor – if the ignitor wire is secure and not damaged but there is still no spark, it’s possible the ignitor itself is faulty.
      • There is no (or not enough) gas supply –
        1. Check that the manual shutoff valve is in the open position.
        2. Have the gas company check that the incoming gas line is pressurized correctly and is not leaking.
        3. If using propane-check that a large enough tank is being used (at least 100 gallon). If the tank has recently been refilled be sure that all the air has been flooded from the gas line.
        4. Have a gas technician check to see if the right size piping was used and if the gas regulator is set correctly.
    • What is a vent free system?
      Vent-free fireplaces rely on indoor air for combustion. A chimney or flue isn't necessary.
      • Vent-free systems add some moisture to the air. It is important that they are installed in well ventilated areas. If not ventilated properly, they may promote mold and mildew growth.
      • It is always a good practice to install CO monitors when using vent free heaters. CO poisoning is a concern if the heater is installed in an area that is not ventilated properly.
      • Some states and other countries (such as Canada) do not allow Vent-free systems.
Document Type de fichier Taille du fichier Produit
Manuel du propriétaire de l'AGC500VF #039;s candidature/pdf 5 Mo Télécharger
Garantie des produits à gaz Ashley Hearth candidature/pdf 106 Ko Télécharger
  • I smell a gas odor when the control knob is in the off position. What do I do?
    • Gas leak:
      1. Do not try to light the appliance.
      2. Do not touch any electrical switch.
      3. Do not use any phone in the building.
      4. Have gas company come and locate the leak.
      5. If the gas company is unavailable have the fire department come and locate the leak.
    • Defective control valve – try to push down or turn the control knob. If it will not push down or turn, the control valve may be defective. **It may still be defective even if the control knob will move.
  • Why will my burner not light?
    • Burner orifice is clogged – clean the same way you would the pilot orifice.
    • Burner orifice diameter is too small – have a gas technician replace the orifice with the correct size.
    • Incorrect gas pressure – see below:
      1. Check that the manual shutoff valve is in the open position.
      2. Have the gas company check that the incoming gas line is pressurized correctly and is not leaking.
      3. If using propane-check that a large enough tank is being used (at least 100 gallon). If the tank has recently been refilled be sure that all the air has been flooded from the gas line.
      4. Have a gas technician check to see if the right size piping was used and if the gas regulator is set correctly.
  • What will cause my pilot to light, but go out when the control knob is released?
    • Control knob is not pressed in all the way – pressing the control knob down allows a flow of gas to the pilot assembly. If not pressed all the way down the pilot will not be self-sustaining.
    • Thermocouple – when the control knob is held down during ignition you are manually opening the gas valve to allow gas flow through the pilot assembly. During normal operation the thermocouple generates a small voltage that holds the gas valve open to allow gas flow. If the thermocouple is bad there will be no gas flow to the pilot assembly once the control knob is released.
      • The thermocouple connection may just be loose.
      • The pilot hood that directs the pilot flame towards the thermocouple may be bent and not allowing contact between the flame and thermocouple.
    • The pilot is clogged – over time a residue will buildup on the orifice and pilot components which will affect the flow of gas. Use a heavy duty pipe cleaner to clear the orifice opening (be sure not to enlarge the opening). Use a non-abrasive scouring pad to clean the thermocouple and other metal components. Use a mild soap and water solution…never anything flammable.
    • Control valve – it is possible that the control valve is damaged or faulty. The only option here is to replace it. This must be done by a licensed gas technician.
    • Orifice isn’t the right size – higher altitudes will affect the operation of a gas heater. Especially when using NG because it is lighter than air. A smaller orifice can be used to obtain the needed pressure at higher altitudes. These are not available through USSC.
  • Why will my pilot not light?
    • Loose ignitor wire – Remove the front cover and check to see if the ignitor wire has come lose. This can happen during shipping.
    • Bad piezo ignitor – if the ignitor wire is secure and not damaged but there is still no spark, it’s possible the ignitor itself is faulty.
    • There is no (or not enough) gas supply –
      1. Check that the manual shutoff valve is in the open position.
      2. Have the gas company check that the incoming gas line is pressurized correctly and is not leaking.
      3. If using propane-check that a large enough tank is being used (at least 100 gallon). If the tank has recently been refilled be sure that all the air has been flooded from the gas line.
      4. Have a gas technician check to see if the right size piping was used and if the gas regulator is set correctly.
  • What is a vent free system?
    Vent-free fireplaces rely on indoor air for combustion. A chimney or flue isn't necessary.
    • Vent-free systems add some moisture to the air. It is important that they are installed in well ventilated areas. If not ventilated properly, they may promote mold and mildew growth.
    • It is always a good practice to install CO monitors when using vent free heaters. CO poisoning is a concern if the heater is installed in an area that is not ventilated properly.
    • Some states and other countries (such as Canada) do not allow Vent-free systems.